Can I Set Up a Tub Myself? Considerations As Well As Steps
Can I Set Up a Tub Myself? Considerations As Well As Steps
Blog Article
What're your thoughts on Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is conveniently easily accessible, the project can relocate quickly; if you have to open up a wall to get rid of the old tub and place the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the job as well as are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will aid you install a brand-new bathtub in your shower room if you have actually already purchased a brand-new tub as well as do not need to transform the arrangement of your previous supply of water pipes.
Your devices and product list ought to make up the following:
Planning for the Installation
First of all, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite problematic due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub until the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and also inspect the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait up until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that entry on How to Install a Bathtub when surfing the web. Do you know another person who is excited about the niche? Why not promote it. Many thanks for your time. Visit us again soon.
Detail
Report this page